Troubleshooting Filters

Observations at the pool itself also may indicate a problem within the filter system. Is there sand or dirt in the pool? This indicates a broken under-drain lateral. In this case, the operator must remove the sand and replace the lateral. Are air bubbles or cloudy water observed at the return inlets? Perhaps the air is being collected in the filter system; usually this is due to the top of the hair and lint strainer being secured or the valves in front of the pump leaking or in need of repacking. Also, if the water level is lower–below the skimmer–the pump is sucking air. Another condition which may lead to air bubbles occurs during vacuuming. If the vacuum hose is full of air, it will travel through the system and back into the pool. Bleeding off the air-relief valve should eliminate the problem; however, if excessive air bubbles continue or there is excessive air in the filter tank, the operator should determine the cause of the air. Nine times out of ten, it will be on the suction side of the pump.

Other Filters

Troubleshooting pressure- and vacuum diatomaceous earth (DE) filters have a set of parameters different from those in dealing with sand filtration. The most common condition is that the pool water is not maintaining water clarity. The filter grids may be clogged with oils, dirt and minerals, which does not allow for DE or alternative media to adhere to the fabric. Another problem is powder backing into the pool. In these cases, the operator should visually inspect all the grids and take appropriate action, either cleaning the grids with an appropriate filter cleaner or replacing the grids that have been torn or damaged.

In a pressure DE system (the pump forces water into the filter), the filter-pressure gauge reads similarly to that of a sand filter. If the filter pressure is high, the filter grids are covered with oils, dirt and minerals, which are clogging the fabric. Most troubleshooting conditions are the same as with a pressure sand filter, when air bubbles or excessive media are backing into the pool; however, the operator should inspect the manifold for damage if unfiltered water is backing into the pool.

The troubleshooting methods of a vacuum DE filter create another set of indicators. As in the case of the pressure DE, if the water clarity is not being maintained, check the filter fabric on the grids for excessive oils, dirt and minerals; also check for inadequate power on the filter grids. If the filter pressure remains high, the operator should inspect the pit to ensure that pool chemicals–particularly calcium products–are not being fed into the media pit. If this is the case, the chemical induction lines need to be relocated to avoid filling the pit with chemicals. In a vacuum DE installation, the pump “sucks” the pool water through the filter system, the opposite of the pressure system. In this case, if air bubbles are coming back through the pool returns, the filter covering may be plugged, causing the pump to pull air from the weakest point in the system above water level. Also, a damaged manifold or blockage in the suction line to the pump may increase air.

The aquatic operator should understand and be fully aware of all the key indicators, gauges and meters, and their functions. In addition, logs must record daily activities, providing the operator with a history. Obviously, the operator must make sure the instruments are functioning and in good repair. In addition, recording clean pressure-gauge readings, the frequency of backwashing, the amount of DE powder for pre-coating the grids and flowmeter readings are all vital in the operator’s daily routine. Any change from the norm is the first step in troubleshooting. Action should be taken immediately to avoid future damage.

Connie Gibson Centrella is a professor and Program Director for the online Aquatic Engineering Program at KeiserUniversity eCampus. She was twice-honored with the Evelyn C. Keiser Teaching Excellence Award “Instructor of Distinction.” Centrella is an industry veteran with over 40 years experience in the pool and spa industry. She is a former pool builder with extensive knowledge in pool construction and equipment installation as well as manufacturing.

Page 2 of 2 | Previous page

Related posts:

  1. Troubleshooting Filters – Test
  2. Troubleshooting Filters – Answer Key
  3. Troubleshooting Filters
  4. Fluid In Motion
  5. Weighing The Options

Leave a Reply

Your email address will not be published. Required fields are marked *

*

HTML tags are not allowed.

  • Columns
  • Departments